Skip to content
Design free

Roofing Calculator

Shingle Calculator: Bundles and Everything Around Them

Enter the building size and the pitch, or a roof area you have measured. The calculator turns it into roofing squares and bundles, then counts the starter strip, the ridge cap, the underlayment, the drip edge and the nails, and prices them at the store.

By The Shed PlannerUpdated 8 min readChecked against 5 sources

Shingle calculator count: bundles of architectural shingles, a starter strip bundle and a ridge cap bundle stacked beside a shed roofIllustration

The short answer

Roof area in square feet divided by 100 is the number of squares, and most architectural shingles come 3 bundles to a square. Add about 10% for waste and round up. A 2,000 sq ft roof is 20 squares, so 66 bundles with 10% extra. For a 10x12 gable shed at 6/12 with a 6 in overhang the roof is 148 sq ft, 1.48 squares, and 5 bundles.

A shingle calculator turns a roof into the bundles to buy. The squares are simple arithmetic; what gets missed is the slope, which makes the roof larger than the floor plan, and the parts that go around the shingles. Enter your building below, or the area if you have already measured the roof.

Calculator

Shingle calculator

Enter the building and the pitch, or the roof area if you have measured it. The calculator works out the roof surface, the squares and the bundles, then the starter strip, ridge cap, underlayment, drip edge and nails that go with them.

Roof
rise 2 ft 6 in126width 10 ft

Bundles of shingles

5
Roof area
148 sq ft
Roofing squares
1.48
Starter strip
1 (49 lin ft)
Hip and ridge cap
1 (12 lin ft)
Synthetic underlayment, 10-square rolls
1
Drip edge, 10 ft pieces
6
Roofing nails, 1-1/4 in
4 lb
Cap nails for the underlayment
1 lb
At the store prices

    Get the whole roof, framed and priced, in the shed designer

    Roof area = footprint plus overhang, times the slope factor for the pitch. Bundles = squares x 3, plus the waste, rounded up. Starter runs along the eaves and up every rake at 120 lin ft per bundle (GAF Pro-Start); ridge cap at 20 lin ft per bundle; underlayment at 15% for laps, doubled below 4/12; drip edge on eaves and rakes with 5% for laps; 4 nails per shingle, about 320 per square. These are the rules the shed designer uses on its own roofs. The wrapper of the product you buy rules.

    How to Calculate How Many Shingles You Need

    Find the roof area

    Roofing is sold by the square, 100 sq ft of roof surface. The surface is larger than the footprint because the roof is tilted. Take the building length and width with the overhangs, multiply them, then multiply by the slope factor for your pitch: 1.054 at 4/12, 1.118 at 6/12, 1.202 at 8/12. The roof pitch calculator gives the factor for any pitch.

    From squares to bundles

    Divide the area by 100 for squares and multiply by the bundles per square on the wrapper, usually 3 for architectural shingles. Add about 10% for waste and round up. A 2,000 sq ft roof is 20 squares, so 66 bundles with 10% extra.

    Worked example: a 10x12 gable shed

    Take the shed designer’s 10x12 gable at 6/12 with a 6 in overhang.

    1. Each slope runs 5 ft plus the 6 in overhang level, which is 6.15 ft along the slope at 6/12.
    2. Two slopes of 12 ft by 6.15 ft make a roof of 148 sq ft, 1.48 squares.
    3. 1.48 x 3 = 4.43 bundles, plus 10% is 4.87, so 5 bundles of shingles.
    4. Starter: 49 lin ft along both eaves and up the four rakes, 1 bundle. Ridge cap: 12 lin ft, 1 bundle.
    5. One 10-square roll of synthetic underlayment, 6 pieces of 10 ft drip edge and about 4 lb of roofing nails.

    The calculator checks these against the designer’s own material list, and on all 28 designer sheds it lands on the same bundle, starter, ridge cap, underlayment, drip edge and nail counts.

    What Else the Roof Needs

    Starter strip and ridge cap

    The starter course goes under the first row so the cutouts and joints of that row are backed, and the ridge cap covers the top after the field shingles are on (ARMA1 Residential Asphalt Roofing Manual). The calculator counts starter along the eaves and up every rake, as GAF3 lays its Pro-Start, at 120 lin ft per bundle. Ridge cap is counted at 20 lin ft per bundle to leave room for the laps; the GAF Seal-A-Ridge bundle we priced says 25.

    Underlayment and drip edge

    Synthetic underlayment is counted with 15% for laps. Below 4/12 the 2021 IRC4 asks for two layers over the whole deck, so the calculator doubles it (R905.2.2 and Table R905.1.1(2)); CertainTeed5 asks for its own waterproofing membrane over the whole deck on those slopes instead. Drip edge is required at the eaves and the rakes of a shingle roof, lapped at least 2 in (R905.2.8.5), and the calculator adds 5% for the laps.

    Nails

    Four nails per shingle is the usual pattern in the instructions we read (GAF3, CertainTeed5 and the ARMA1 bulletin), about 320 per square. Roofing nails must be galvanized, stainless, aluminum or copper, at least 12 gauge with a 3/8 in head, long enough to go 3/4 in into the deck or through it (R905.2.5 and R905.2.6). Synthetic underlayment takes plastic cap nails, counted at about one per square foot.

    Pitch Limits for Shingles

    Asphalt shingles go on at 2/12 or steeper, never below (R905.2.2). From 2/12 up to 4/12 they are a low-slope roof that needs the double underlayment above or the maker’s own method. Below 2/12, choose standing seam metal or a membrane. Where your area has a history of ice damming, the code asks for an ice barrier 24 in inside the wall line, though detached accessory buildings with no conditioned space are exempt (R905.1.2).

    Shingles for a Shed or a House

    The math is the same for any gable or single-slope roof. For a house with hips, valleys or dormers, measure the area plane by plane, enter it with “I know the area”, and add the length of the hips and ridges for the cap. For a shed, the shed designer draws the roof and lists every bundle, sheet and nail with the frame, and how to shingle a shed roof walks through laying them.

    Sources

    Every number in this guide that does not come from our own shed designer was checked against these 5 documents, numbered in the order the text first cites them and read on Sep 30, 2026. 5 are codes, agencies, makers and stores.

    1. 1Asphalt Roofing Manufacturers Association (ARMA)Residential Asphalt Roofing Manual, Design and Application Methods (2014)
    2. 2Asphalt Roofing Manufacturers Association (ARMA)Technical bulletin: Nail Application of Asphalt Shingles
    3. 3GAFInstallation Instructions: Timberline HDZ and related lines
    4. 4International Code Council2021 International Residential Code, Chapter 9: Roof Assemblies
    5. 5CertainTeedMaster Craftsman Shingle Applicator's Manual, Landmark Series

    Questions

    Anything else? Write to us or browse every guide.

    Questions people ask

    Eight, for the shed designer's 12x16 gable at 6/12 with a 6 in overhang: the roof is 233 sq ft, 2.33 squares, and 3 bundles a square plus 10% rounds up to 8. Add 1 bundle of starter strip and 1 of ridge cap. A steeper pitch or a wider overhang adds area, so enter your own numbers.

    Measure each roof plane along the slope, eave to ridge, and along the eave, and multiply. Or measure the building on the ground, add the overhangs, and multiply by the slope factor for the pitch: 1.118 at 6/12. Add the planes, divide by 100 for squares.

    Thirty, at 3 bundles a square, which is how most architectural shingles are packed; the GAF Timberline bundle we priced covers 33.33 sq ft. With 10% for waste and cuts, buy 33. Not every shingle is packed 3 to a square, so check the coverage on the wrapper.

    The calculator starts at 10%, the figure the shed designer uses on its own simple gable and lean-to roofs. Roofs with hips, valleys and dormers waste more in cuts, so raise it for those.

    Plan on both. The starter course fills the gaps under the cutouts and joints of the first course, and the hip and ridge cap covers the top joint after the field shingles are down (ARMA). GAF's instructions run its starter along the eaves and up the rakes, at 120 lin ft per bundle of Pro-Start.

    Design it, then build it

    Your backyard deserves a shed that fits.

    Change the size, the roof, the doors and the windows. The span checks, the wall bracing and the materials list follow every change. Free, no account.

    Design my shed, free
    Designing
    Free
    Builder's plan
    $35 once
    Account
    Not needed
    A finished board-and-batten gable shed with double doors at sunsetIllustration