Skip to content
Design free

Size, cost and permits

What Can I Store in an 8x10 Shed?

An 8x10 shed is 80 sq ft with a 48 inch door opening. The door and the wall length decide what fits, so measure those two things before you load it.

By The Shed PlannerUpdated 9 min readChecked against 3 sources

What Can I Store in an 8x10 Shed?: the 8x10 gable shed from our designer, drawn at the stage this guide covers

The short answer

An 8x10 shed has 80 sq ft of floor, about 89 inches between the side walls and a 48 inch door opening. That holds garden tools, a push mower, bikes, bins and wall shelving. A riding mower with its deck down is 55.2 inches wide on one example tractor, so it does not pass the door.

An 8x10 shed is 80 sq ft of floor with a 48 inch door opening, and that is enough for tools, a push mower, a couple of bikes and a wall of bins. It is not enough for a riding mower, because the door is narrower than the machine. The rest of this guide shows the real inside dimensions, what fits where and how to lay it out so you can still walk in.

What fits in an 8x10 shed

Think of an 8x10 as 3 limits: the 80 sq ft of floor, the wall length you can put shelves on and the 48 inch opening everything has to pass through. The designer’s default 8x10 gable shed has an 88-3/4 inch wall, a 48 inch door on the front and a 24 x 24 inch window on one side wall. From the gravel pad to the ridge it stands 10 ft 9-3/8 in.

The door is the first limit

Everything you own has to go through the opening before it can use the floor. The default 8x10 frames a 48 inch opening for a pair of doors, and once the hinges and the open door leaves take their share, the clear width is a little less. Measure the widest thing you plan to store, add a few inches, and compare it with 48.

The walls are the second

An 8x10 is small on the floor and generous on the walls. The side walls are 88-3/4 inches tall, which is room for 3 or 4 shelves one above the other, and the studs stand 16 inches apart, so a shelf bracket or a hook always has a stud within reach. Plan around the walls and the floor stays free.

What that means in practice

  • Long-handled tools, a wheelbarrow, a push mower, a trimmer and a few bikes go in without any trouble.
  • Bins and shelving along the 2 side walls give you most of the storage.
  • Anything wider than 48 inches does not go through the door, however much floor is inside.

The real dimensions of an 8x10

The label says 8x10, but you live inside the walls. Studs and siding take about 7 inches off each direction, so the usable floor is smaller than 80 sq ft, and the numbers that matter are these.

Measure 8x10 gable shed
Outside floor 96 x 120 in (80 sq ft)
Between the side walls about 89 in
Front to back about 113 in
Wall height 88-3/4 in
Door opening 48 in wide
Top of ridge above the gravel pad 10 ft 9-3/8 in

The width and depth between the walls come from the framing list in the engine: the front wall runs 89 inches between the side walls, and the side walls carry a 113 inch cap plate. Treat them as the working room, then check them against your own build, since a different door, window or siding thickness moves them a little.

The 8x10 gable shed as the designer draws it. the door and its framing at the front, one window on a side wall, and a 6/12 roof.Open this design

What the walls give you

Shelving goes on walls, so count wall length, not floor. Each side wall is about 113 inches long inside and the back wall about 89 inches. That is roughly 315 inches of wall before the door and window take their share. If you set 18 inch deep shelves on both side walls, the aisle between them is about 53 inches, which is wider than the door. Once you go past that, you are trading walking room for storage.

If you are still choosing between sizes, the shed sizes guide lists the floor, wall and door of every plan, so you can see what a step up buys.

What you can store

What can I store in an 8x10 shed: a cutaway of a small shed with a lawn mower, a bike, a wall shelf of tools and stacked storage bins.Illustration

Garden tools and a push mower

Hang long-handled tools on the wall in a rack, handles up, so they take no floor. Put the push mower and the wheelbarrow next to the door, where you reach them first and where nothing has to be moved to get them out. A push mower is narrow enough for a 48 inch opening, and with the handle folded it parks against a side wall.

Bikes

Bikes are longer than they look, and they stick out sideways when the handlebars turn. Hang them from wall hooks by the wheel, or stand them against the back wall in a row, so the floor stays open. Leave the side wall with the window free for light, since a bike hung over a window blocks it.

Bins and shelving

Bins on shelves are the best use of an 8x10. Stack the heavy bins low and the light ones high, label the ends that face the aisle, and keep the shelf depth to what you can reach with the door open. The walls are the storage in this shed, so spend on shelving before you spend on floor space.

A riding mower?

Not through a 48 inch door. A John Deere dealer’s spec sheet for the S120 lawn tractor with its 42 inch Edge deck lists it at 55.2 inches wide with the deck. With the discharge deflector raised for storage it is 46.5 inches wide, which leaves 1-1/2 inches in a 48 inch opening, before the hinges and the open door leaves take their share. That is one machine from one dealer, so measure your own: other models and wider decks are wider.

The designer will frame a wider door, but it refuses one too wide for the front wall with its framing: a 96 inch door on a 96 inch wide shed is an error, and a door too tall for the wall is refused too. For a riding mower, plan a wider shed and a wider door instead, as the lawn mower storage shed guide walks through.

Layout ideas for an 8x10

Put the door end first. The first 3 ft inside the door should hold what you use every week, and the back wall what you use twice a year.

A center aisle

Keep a clear strip from the door to the back wall, with shelves on both side walls. This is the most common plan and it works: nothing blocks the door, and each shelf is within an arm’s reach of the aisle. Hang the tools on the back wall, where the aisle ends.

One side for shelves, one for big items

If your biggest item is a push mower, a wheelbarrow or a bike, give one side wall to wheeled things and the other to shelves. The wheeled side stays free, so you roll things in and out in a straight line.

Mark it out before you load it

Tape the layout on the floor of the shed before anything goes in, or on your driveway at 96 x 120 inches. Lay the mower, the bikes and the wheelbarrow on the outline and see how the aisle works out. It takes 10 minutes and it shows you what the arithmetic cannot: whether you can open the door leaf all the way, and whether a bike’s handlebars catch the shelf.

Check before you cut

Measure these 4 things

The widest item you store, the door opening, the length of the longest shelf wall and the aisle you want. If the widest item is more than the door opening, the floor space does not matter.

No loft

The designer has no loft option, and none of the 8x10 plans include one. Under a 6/12 gable roof the space above a loft floor is small as well. If you want to think about one anyway, the shed loft guide shows the head room and the joist spans. For most 8x10 sheds the wall shelves do the same job with no new framing.

What not to store

Check the label on anything that can burn, leak or freeze, and follow what it says. Fuel, propane, paint, pesticides and pool chemicals each come with storage directions, and your local fire code may add its own. We have not found one rule that covers all of them, so read the label and ask your fire department when in doubt.

Beyond the labels, 3 things go wrong in a plain wood shed.

Heat and cold

A storage shed has no insulation, so treat it as a box that follows the weather. Anything that spoils, cracks or separates at either end of the thermometer belongs in the house. If a product label gives a temperature range, believe it.

Damp

A floor on skids sits close to the ground. Keep paper, cloth, cardboard and anything that rusts up on shelves, off the floor and away from the walls, and leave a little air behind the bins.

Pests

Seed, pet food and birdseed in paper bags invite mice. Use a lidded bin, and do not leave open food in a shed you open once a month.

Build or buy an 8x10

Your options for an 8x10 are a kit, an installed shed or building from plans. The right one depends on how much of the work you want to do and how exactly you want the inside to fit the things you listed above.

Kits and installed sheds

We read these prices on homedepot.com on Sep 30, 2026, for the Bronx Terminal store and delivery ZIP 30303:

Option Listing Price
Little Cottage Co. Value Gable 8x10 precut kit DIY kit $1,809.00
Handy Home Meridian 8x10 kit with floor and double doors DIY kit $2,299.00
Tuff Shed Tahoe Sierra 8x10, primed, 6 ft sidewall Professionally installed $3,179.00
Tuff Shed Tahoe Sierra 8x10, painted Professionally installed $3,569.00

We did not read what each kit includes, so do not assume shingles, siding or paint are in the box. The Tuff Shed Sierra has a 6 ft sidewall, while the designer’s wall is 88-3/4 inches, so they are not the same building. On a separate model, the Tuff Shed Premier Tall Ranch 8x10 base price works out to $50.99 per sq ft (ZIP 67446, one model, one day).

Building from plans

Building lets you size the door and the walls to what you store, which a kit or an installed shed does not. If a riding mower is on your list, that choice matters more than the price. To build it yourself, the plan’s material list is on the shed material list guide. The 8x10 uses 101 boards, 5 sheets of OSB and 4 bundles of shingles. The table below prices every line:

Shell $2,713.58, shed materials $3,498.44

Budget build $3,435.45 to typical $3,498.44.

BuyItemEachLine
Lumber
34x6 pressure-treated (ground contact), 10 ftdelivery-only card$19.38$58.14
92x6 pressure-treated (ground contact), 8 ft$10.78$97.02
22x6 pressure-treated (ground contact), 10 ft$12.68$25.36
12x6 pressure-treated (ground contact), 16 ft$21.18$21.18
562x4 framing lumber, 8 ft$4.35$243.60
62x4 framing lumber, 10 ft$7.83$46.98
12x6 framing lumber, 10 ft$12.52$12.52
12x6 framing lumber, 12 ft$14.98$14.98
52x6 framing lumber, 16 ft$19.96$99.80
12x8 framing lumber, 10 ft$14.16$14.16
22x12 framing lumber, 8 ftdelivery-only cardprice from Menards.com, no store selected, Oct 10, 2026The card gives the grade, #2 & Better, not the species.$20.12$40.24
121x4 exterior trim board, 8 ft$10.58$126.96
21x6 exterior trim board, 12 ft$25.55$51.10
Sheet goods
3 sheets3/4" treated tongue-and-groove subfloor, 4x8ship-to-store cardprice from Menards.com, no store selected, Nov 16, 2026Price before Menards' 11% mail-in rebate of $9.90 ($80.09 after the rebate), which is store credit, not a price cut.$89.99$269.97
10 sheetsPanel siding, 19/32" T1-11 plywood, APA Rated Siding 303, Exterior (the wall bracing counts on this panel: a plywood wood structural panel 19/32" thick, over the 3/8" IRC Table R602.10.4 asks for CS-WSP; the bracing calculation does not cover a different siding or a thinner panel; the portal frame needs 7/16" or more), 4x8$46.78$467.80
1 sheetPanel siding for the gable ends, 4x8$46.78$46.78
1 rollHouse wrap (water-resistive barrier), 9 ft x 100 ft rollship-to-store cardprice from Menards.com, no store selected, Oct 10, 2026Closest available: a 9 x 100 ft woven house wrap roll; the card does not state its ASTM E2556 type and its product page could not be read. Check that the roll's label says ASTM E2556 Type 1 or 2 before you buy, or type the price of the wrap you choose.$82.67$82.67
5 sheets7/16" OSB roof sheathing, 4x8$11.98$59.90
2 piecesZ-flashing for the horizontal siding joints, 10 ft piecesprice from Home Depot, Hamilton Mill store (ZIP 30011), Sep 30, 2026$5.98$11.96
1 sheet1/2" plywood for the header spacers, 4x8price from Home Depot, Hamilton Mill store (ZIP 30011), Oct 8, 2026$27.81$27.81
Roofing
4 bundlesAsphalt shingles, 3 bundles per square$44.97$179.88
1 bundleStarter strip shingles$54.97$54.97
1 bundleHip and ridge cap shingles$63.97$63.97
1 rollSynthetic roof underlayment, 10-square roll$74.98$74.98
2 lbPlastic cap nails, 1-1/2", for the underlayment and the house wrapprice from Home Depot, Hamilton Mill store (ZIP 30011), Oct 11, 2026$12.91$25.82
5 piecesDrip edge, 10 ft pieces$8.48$42.40
Fasteners and hardware
16 lbFraming nails, 16d common, hot-dip galvanized, 3-1/2" x 0.162"$31.73$126.92
5 lbToenail nails, 10d box, hot-dip galvanized, 3" x 0.128"ship-to-store card$19.38$19.38
12 lbSiding nails, 8d common, hot-dip galvanized, 2-1/2" x 0.131"ship-to-store card$26.98$80.94
4 lbRoof sheathing nails, 2-1/2" (8d)ship-to-store card$26.98$26.98
2 lbExterior screws for the subfloor, 2", rated for treated lumber$34.47$34.47
18Rafter-to-plate connectors (hurricane ties)$0.98$17.64
9Ridge straps, 1-1/4" x 20 ga galvanized steel, 18" long (Simpson Strong-Tie LSTA18 or equal)stock not read on the pageprice from Menards.com, no store selected, Oct 10, 2026Menards sells MiTek, not Simpson: its page lists this strap with the Simpson Strong-Tie reference number LSTA18, so it is the plan's LSTA18 or equal. The page says the strap is recommended for interior applications and not for treated lumber: the ridge straps go on the untreated rafters under the roof sheathing, inside the shell. The page also says it is not sold online, only in store.$1.38$12.42
2Portal header straps, 1-1/4" x 18" galvanized steel (Simpson Strong-Tie LSTA18 or equal, rated 1,000 lb or more)stock not read on the pageprice from Menards.com, no store selected, Oct 10, 2026Menards sells MiTek, not Simpson: its page lists this strap with the Simpson Strong-Tie reference number LSTA18, so it is the plan's LSTA18 or equal. The page says the strap is recommended for interior applications and not for treated lumber: the portal straps go on the inside face of the wall, header to door post, both untreated, inside the shell. The page prints no load rating, so check the strap you buy is rated 1,000 lb or more, as the line asks. The page also says it is not sold online, only in store.$1.38$2.76
2 lbNails for the ridge and portal straps, 10d common, 3" x 0.148", hot-dip galvanizeddelivery-only cardprice from Menards.com, no store selected, Oct 10, 2026$4.97$9.94
4Framing anchors for the portal frame, Simpson Strong-Tie LTP4 lateral tie platesship-to-store cardprice from Home Depot, Hamilton Mill store (ZIP 30011), Oct 10, 2026$0.78$3.12
1 boxSimpson Strong-Drive SD9112 connector screws, #9 x 1-1/2", for the LTP4 platesprice from Home Depot, Hamilton Mill store (ZIP 30011), Oct 10, 2026$16.65$16.65
7 lbNails for the portal frame sheathing, 8d common, 2-1/2" x 0.131", hot-dip galvanizedship-to-store card$26.98$53.96
3 lbRoofing nails, 1-1/4"$21.00$21.00
2 tubesConstruction adhesive (subfloor)$7.68$15.36
4Earth auger anchors, 30 in or longer, with a holding rating published by their maker, plus galvanized cable and wire-rope clipsshipped by the sellerprice from Amazon.com, sold by Amazon, Oct 13, 2026Sold and shipped by Amazon.com. The maker's listing gives the rating: four 30-inch anchors with 2,400 lb. ultimate holding power each, plus eight 1/8 in galvanized clamps and galvanized cable (the title says 100 ft, the feature list 60 ft).$50.89$50.89
180 nailsConnector nails for the hurricane ties, 0.131" x 2-1/2" galvanizedprice from Home Depot, Hamilton Mill store (ZIP 30011), Oct 8, 2026$8.55$17.10
16Plywood H-clips for 7/16" sheathingprice from Home Depot, Hamilton Mill store (ZIP 30011), Oct 8, 2026$12.22$12.22
Flashing, sealants and finish
1 pieceZ-flashing for the door and window heads, 10 ft piecesprice from Home Depot, Hamilton Mill store (ZIP 30011), Sep 30, 2026$5.98$5.98
1 rollWindow flashing tape, 4" x 75 ft rollship-to-store cardprice from Home Depot, Hamilton Mill store (ZIP 30011), Oct 8, 2026$36.42$36.42
3 tubesExterior acrylic-latex caulk, paintable, 10.1 ozprice from Home Depot, Hamilton Mill store (ZIP 30011), Oct 8, 2026$2.98$8.94
2Exterior primer, 1 gallonprice from Home Depot, Hamilton Mill store (ZIP 30011), Oct 8, 2026$29.98$59.96
4Exterior paint or solid stain, 1 gallonstore pickup offered, stock count not shownprice from Home Depot, Hamilton Mill store (ZIP 30011), Oct 8, 2026$49.98$199.92
Doors and windows
1Shed window with a nailing flange, for a 24" x 24" rough openingprice from Menards, Columbus store (ZIP 43229), Oct 8, 2026Closest available: a 24 x 24 in vinyl sliding window, 23-1/2 x 23-1/2 in tip to tip, with a mounting flange. Confirm the opening before you buy, or type the price of the unit you choose.$46.99$46.99
Door build
62x4 framing lumber, 92-5/8" precut stud, for the door frames$4.15$24.90
41x2 furring strip, 8 ft, for door stops and the astragalprice from Home Depot, Hamilton Mill store (ZIP 30011), Oct 8, 2026$1.54$6.16
1 sheetPanel siding for the door skins, 4x8$46.78$46.78
6Heavy-duty T-hinges, 8"price from Home Depot, Hamilton Mill store (ZIP 30011), Oct 8, 2026$9.50$57.00
1Two-way gate latch, opens from inside and outside without a keyship-to-store cardprice from Home Depot, Hamilton Mill store (ZIP 30011), Nov 17, 2026$28.98$28.98
1Padlock hasp, for locking the shed when it is emptyprice from Home Depot, Hamilton Mill store (ZIP 30011), Oct 8, 2026$5.97$5.97
2Barrel bolts for the fixed leafprice from Home Depot, Hamilton Mill store (ZIP 30011), Oct 8, 2026$8.27$16.54
2Door pull handleprice from Home Depot, Hamilton Mill store (ZIP 30011), Oct 8, 2026$4.98$9.96
1 boxExterior screws for the door frames and stops, 2-1/2"price from Home Depot, Hamilton Mill store (ZIP 30011), Oct 8, 2026$15.38$15.38
2 boxesExterior screws for the door skins, 1-1/4"price from Home Depot, Hamilton Mill store (ZIP 30011), Oct 8, 2026$10.98$21.96
2 tubesConstruction adhesive (door skins), 10 ozprice from Home Depot, Hamilton Mill store (ZIP 30011), Oct 8, 2026$7.48$14.96
Temporary bracing
92x4 framing lumber, 8 ft, for temporary braces and stakes and ridge posts$4.35$39.15
22x4 framing lumber, 16 ft, for temporary braces and stakes and ridge posts$12.47$24.94
1 boxExterior screws for the temporary braces, 3"$24.88$24.88
Foundation
1 rollLandscape fabric, enough to cover 10' x 12'price from Home Depot, Hamilton Mill store (ZIP 30011), Oct 27, 2026$19.97$19.97
Shell: structure, siding, roof and foundation$2,713.58
Finish: doors, windows, trim, flashing, caulk, primer and paint$784.86
Shed materials, doors built from the plan (the cheaper door for this size), 64 of 64 lines priced$3,498.44
Materials priced: $3,498.44 · every line priced · Excluded: tax, delivery, labor, permits, tools
Labor if you hire it out, apart from the materials$640 to $4,800
Labor only, building the shed from the plan (framing, siding, roof, doors), materials not included, for the shed as a shell: insulating, wiring and lining the inside are not in this range. Published ranges (HomeGuide, Aug 2025: $8 to $60 per sq ft; Fixr, Mar 2024: $25 per sq ft), per sq ft from the examples they quote (a 10x10 custom build and a 10x12 wooden shed). 80 sq ft at $8 to $60 per sq ft, middle about $2,000. A range from guides, not a quote; get two local quotes. Separate from the materials above and not in their sum.
With pre-hung doors instead (door not priced), 53 of 54 lines$3,199.87
Budget build: the cheapest spec of this plan that passes every check
Frame rafters at 24 in on centerinstead of 16 in; this design passes every span check at 30 psf snow with it-$62.99
Budget build, you save $62.99$3,435.45
Optional: no window as well, $146.01 less$3,289.44
Site prep, not in the shed materials total
2.0 cu ydGravel base: compactable crushed stone, loose, for a 4" compacted pad 1 ft wider than the shed on every sidePriced as bulk crushed stone delivered by the cubic yard, an average estimate: East Coast Lumber & Building Supply (East Hampstead, NH) listed 3/4 in crushed stone at $69.95 per cubic yard on Sep 30, 2026, delivered in loads of 3 to 8 yards; delivery fees and prices vary by area. Bagged instead, the same stone would be $698.76 (108 bags of 0.5 cu ft at $6.47, Home Depot, Hamilton Mill store (ZIP 30011), Sep 30, 2026): bags make sense only for a small top-up. Site prep, not in the shed materials total.$69.95 a bag$139.90

Bulk prices and bigger packs on this list

  • Connector nails: the list's 2 boxes of 1 lb are the same Grip-Rite 8d galvanized common nail it buys in 5 lb boxes for the siding and the roof sheathing. Buy 5 boxes of 5 lb for both jobs instead and save $44.08: $26.98 for 5 lb (model 8HGC5, Home Depot, Hamilton Mill store (ZIP 30011), Oct 8, 2026) against $8.55 for 1 lb (model 8HGC1, Home Depot, Hamilton Mill store (ZIP 30011), Oct 8, 2026).
  • 2x4 x 8 ft: your list buys 65 boards, which reaches the bulk price. $27.95 less if the store applies it at the register: the card shows $3.92 a board at 50 or more, $4.35 below that (Home Depot, Bronx Terminal store, Sep 30, 2026).

Tips from the tiers on the store cards, dated as the prices. They are not in the totals above.

Left over in part-used boxes

Boxes of nails, screws and clips come whole, so about $148.07 of this list stays in part-used boxes: the shed itself uses that much less. Rolls and bundles of roofing and house wrap are sold whole too: about $185.87 of them stays unused on a small design.

  • Framing nails: the shed uses 16 lb of the 20 lb you have to buy, about $25.38 left over.
  • Siding nails: the shed uses 12 lb of the 15 lb you have to buy, about $16.19 left over.
  • Roof sheathing nails: the shed uses 4 lb of the 5 lb you have to buy, about $5.40 left over.
  • Exterior screws for the subfloor: the shed uses 2 lb of the 5 lb you have to buy, about $20.68 left over.
  • Simpson Strong-Drive SD9112 connector screws, #9 x 1-1/2", for the LTP4 plates: the shed uses 48 screws of the 100 screws you have to buy, about $8.66 left over.
  • Nails for the portal frame sheathing: the shed uses 7 lb of the 10 lb you have to buy, about $16.19 left over.
  • Roofing nails: the shed uses 3 lb of the 5 lb you have to buy, about $8.40 left over.
  • Plywood H-clips for 7/16" sheathing: the shed uses 16 clips of the 50 clips you have to buy, about $8.31 left over.
  • Exterior screws for the door frames and stops: the shed uses 69 screws of the 100 screws you have to buy, about $4.77 left over.
  • Exterior screws for the door skins: the shed uses 106 screws of the 200 screws you have to buy, about $10.32 left over.
  • Exterior screws for the temporary braces: the shed uses 40 screws of the 900 screws you have to buy, about $23.77 left over.
  • House wrap: the shed uses 337 sq ft of the 900 sq ft in the roll or bundle you have to buy, about $51.71 left over.
  • Starter strip shingles: the shed uses 41 lin ft of the 120 lin ft in the roll or bundle you have to buy, about $36.19 left over.
  • Hip and ridge cap shingles: the shed uses 10 lin ft of the 20 lin ft in the roll or bundle you have to buy, about $31.99 left over.
  • Synthetic roof underlayment: the shed uses 1.2 squares of the 10 squares in the roll or bundle you have to buy, about $65.98 left over.

Quantities from the shed designer for the 8x10 gable plan, with the doors built from the plan: the total uses whichever door choice costs less for this size, and for the 8x10 gable that is building them from the plan. Prices: Home Depot, Bronx Terminal store, captured Sep 30, 2026, except the lines that name another store, before sales tax and delivery. Lines marked nearby, delivery-only or ship-to-store were not in stock at their store; a line marked pickup offered had no stock count on its page. On Menards.com, no store selected no store stock was shown at all. Every shed line has a price. Shed materials covers lumber, sheet goods, roofing, fasteners and hardware, flashing, caulk, primer and paint, the windows and doors, and the foundation parts; the gravel base is site prep, priced on its own below the total. The shell is the structure, siding, roof and foundation: framing lumber, sheathing and subfloor, siding, roofing, nails, screws and connectors, the skids or blocks, anchors and fabric, and the temporary braces; the finish is what closes and finishes it: the doors (their frames, skins, stops and hardware, or the pre-hung units), the windows, the trim boards, the head flashing, flashing tape, caulk, primer and paint. This sum mixes five stores: 2x12 portal header, house wrap (closest available), ridge straps, portal straps and strap nails are priced at Menards.com, no store selected, Oct 10, 2026; treated subfloor panels at Menards.com, no store selected, Nov 16, 2026; Z-flashing at Home Depot, Hamilton Mill store (ZIP 30011), Sep 30, 2026; header-spacer plywood, connector nails, H-clips, flashing tape, caulk, primer, paint, 1x2 stops, hinges, hasp, barrel bolts, door pull, door screws, skin screws and door adhesive at Home Depot, Hamilton Mill store (ZIP 30011), Oct 8, 2026; underlayment cap nails at Home Depot, Hamilton Mill store (ZIP 30011), Oct 11, 2026; LTP4 framing anchors and SD9112 screws at Home Depot, Hamilton Mill store (ZIP 30011), Oct 10, 2026; ground anchors at Amazon.com, sold by Amazon, Oct 13, 2026; windows (closest available) at Menards, Columbus store (ZIP 43229), Oct 8, 2026; two-way latch at Home Depot, Hamilton Mill store (ZIP 30011), Nov 17, 2026; Landscape fabric, enough to cover 10' x 12' at Home Depot, Hamilton Mill store (ZIP 30011), Oct 27, 2026; every other line at Home Depot, Bronx Terminal store, Sep 30, 2026. Prices change by store and by day.

You can open the exact size in the shed designer, or get the framing and cut list from the 8x10 gable shed plan. Prices are volatile, so check them in your own store before you buy.

Sources

Every number in this guide that does not come from our own shed designer was checked against these 3 documents, numbered in the order the text first cites them and read between Sep 30, 2026 and Oct 10, 2026. 2 are codes, agencies, makers and stores; 1 is a secondary source (shed sellers' and builders' guides), marked, used only where no code, agency or maker gives a number.

  1. 1JLD-Laguë (John Deere dealer)Secondary sourceLawn Tractor | S120 | 22 HP
  2. 2The Home Depot, Bronx Terminal storeSearch results and shelf prices for "tuff shed installed 10x12"
  3. 3The Home Depot, Bronx Terminal storeSearch results and shelf prices for "wood shed kit 10x12 pre-cut"

Questions

Anything else? Write to us or browse every guide.

Questions people ask

Read the label on anything flammable, pressurized or sensitive to heat and cold, such as fuel, propane, paint, pesticides and pool chemicals, and follow what it says about storage. Your local fire code may add rules of its own. Keep irreplaceable papers, photos and food out of a shed that is not insulated or sealed from damp.

A precut 8x10 kit from Home Depot listed at $1,809.00 and a professionally installed Tuff Shed Tahoe Sierra 8x10 at $3,179.00, both read on Sep 30, 2026. Building from plans means pricing every line yourself, which our cost table does for the 8x10 plan. Kits and installed sheds include things you would otherwise buy and cut, so compare what each one contains.

Garden tools, a push mower, bikes, bins of seasonal gear, camping equipment and hardware fit best, because they stand on shelves and hooks along the walls. Keep the heavy and wheeled items near the door and the things you use once a year at the back.

An 8x10 storage unit and an 8x10 shed have the same floor area, 80 sq ft, so the same footprint of furniture or gear fits on the floor. The difference is the door, the shelving you can add and how the building is built and sealed, so compare those before you choose one.

Design it, then build it

Your backyard deserves a shed that fits.

Change the size, the roof, the doors and the windows. The span checks, the wall bracing and the materials list follow every change. Free, no account.

Design my shed, free
Designing
Free
Builder's plan
$35 once
Account
Not needed
A finished board-and-batten gable shed with double doors at sunsetIllustration