The short answer
You can move a shed on rollers and pipes, on a jack and trailer, with a professional shed mover, or by taking it apart. A move on your own lot ran $250 to $375 and a local move $400 to $500 in Bob Vila's May 2024 breakdown, while a new 10x12 shed costs you the materials in the table below.
Most sheds can be moved in one piece, and you can do it yourself if the shed is small, the floor is sound and the path is clear. If not, a shed mover does it for a few hundred dollars. If the floor is rotten, it is cheaper to take the shed apart for parts and build new.
This guide covers four ways to move a shed: rollers and pipes, a jack and trailer, a professional shed mover, and taking it apart. For each one you get the size it suits, the tools, the risk, and what it costs from sources we name. Then it compares the cheapest move with the cost of building new from our shed designer.
Which way to move a shed
Two things decide the method: how far the shed has to go and how it is built.
A shed that goes across your own lot, a few yards to a new spot, can slide on rollers. A shed that has to leave the lot needs a trailer or a mover. A shed with 4x6 timbers under the floor, a shed on skids, is the easy one: the timbers are the runners, and they take the weight of the lift and the slide. A shed on blocks or on a slab has no runners. For those, a mover has to add timbers first, or the shed has to come apart.
Whole or in pieces
If the shed fits through the gate and the path, move it whole. A small shed is one job and one day. If the walls are too wide for the path, or the shed is rotten, taking it apart is the safer choice.
Own lot or another address
A move on your own lot stays off public roads. A move to another address is a transport job: the trailer, the load width, the straps, and in some states a permit. Bob Vila notes that load permits vary by state, so ask your state transport office if your load is wide.
Before you move it
Most of the work is done before the shed moves.
Empty it and check the floor
Take everything out, including the shelves and the loft boards. Look under the floor with a flashlight. Soft wood or rot at the sill means the lift can crack the frame, so repair it first or plan to build new.
Measure the path
Measure the width of the shed at its widest point, the roof overhang included. Then measure the gate, the gap between the house and the fence, and any tree branch. Mark a clear line from the old spot to the new one. Walk the line and note any slope: a shed on rollers will pick up speed on a slope, and nobody should stand downhill of it.
Get the new base ready
The new base should be done before the shed moves. A level gravel shed base is the usual choice for a shed on skids, and you can level the spot with our guide to leveling ground for a shed. Digging for the new pad? Call 811, the free national before-you-dig line, a few business days before you start (Common Ground Alliance, call811.com).
Permits and setbacks
A shed that is allowed on the old lot is not automatically allowed on the new one. Setbacks, size limits and permits are different at every address. Check with your local building department, and read our shed permits guide first.
Way 1: Rollers and pipes
This is the cheapest method, and it suits a small shed on your own lot. Bob Vila budgets about $100 for rollers such as PVC pipe and mounting planks for an on-site move.
What you need
You need three or four rollers, which are lengths of sturdy pipe or round timber, a pry bar, a bottle jack, planks or a skid-sheet runway, and helpers. The rollers go under the skids, and the shed rolls forward as the back rollers are carried to the front.
How it goes
Jack up one end of the shed, slide two rollers under the skids, lower it, then do the other end. Push the shed forward slowly. As a roller comes out at the back, carry it round to the front. Keep a spotter at each corner and keep your feet out of the line of travel.
The risk
Rollers need firm, fairly level ground. On soft lawn they sink, and on a slope the shed can run. A shed with a lot of weight in the walls and the roof will rack if one corner lifts before the others. Move it a short distance only.
Way 2: Jack and trailer
A trailer is the usual way to get a small or mid-size shed to another address. Bob Vila notes that a larger shed may need a trailer or forklift rental, and that very large sheds may need a tilt trailer, a flatbed truck, a forklift or a crane.
What you need
A trailer with a deck wider and longer than the shed floor, or a tilt trailer, a vehicle rated to tow it, ratchet straps, a pair of bottle or screw jacks, 4x4 cribbing blocks, and helpers. The shed floor must carry the lift.
How it goes
Lift one side with the jacks, slide the cribbing under it, and keep raising it, one corner at a time, until the skids clear the trailer deck. Roll or winch it on. Center it so the weight sits over the axle, and strap it down. Drive slowly with a spotter.
The risk
A shed that is racked or old can twist when lifted. A tall roof or a wide overhang can hit branches and signs. Check your trailer rating and the load width before you commit. Insurance rules for a trip on public roads are your own to check.
Way 3: A professional shed mover
A shed mover brings a trailer and lifting gear made for the job. This is the right call for a larger shed, a shed with no skids, a long trip, or a tight yard.
What it costs
Prices below come from two sources we opened in October 2026. They are examples, not a quote for your yard.
| Source | Move | Price |
|---|---|---|
| Bob Vila, May 29, 2024 | On-site, same property | $250 to $375 |
| Bob Vila, May 29, 2024 | Local, typically under 100 miles | $400 to $500 |
| Bob Vila, May 29, 2024 | Long distance, 100 miles or more | about $4,000 |
| Bob Vila, May 29, 2024 | Extra-wide load | $6,000 to $7,500 |
| We Move Sheds (North Carolina), price page read October 2026 | In-yard, 8 or 10 ft wide shed with skids | $685.00 |
| We Move Sheds (North Carolina), price page read October 2026 | In-yard, 12 ft wide shed with skids | $750.00 |
Bob Vila also gives $1 to $2 per mile for distance moves and $910 to $2,530 for professional shed movers. We Move Sheds includes 4 hours of relocation, blocking and leveling, then charges $65.00 per hour, and says the prices are site-unseen estimates. The date on that page is a 2022 copyright footer, so treat the prices as a guide, not a current quote.
What adds to the price
The same mover lists extras: $375 to anchor a storage building at the new site, $25 per old anchor removed, $100 to add 4x4 skids ($150 for larger buildings, plus the material), $5.00 per extra block on a less level site, $25 to remove ramps or steps, and $125 if the site is not ready on moving day. A site that is not ready, a sloped yard and tight access are what make a quote climb.
Get quotes the right way
Ask at least two movers for a written quote. Give them the shed width, depth and height, whether it has skids, the path width, and both addresses. Ask what is included, and what happens if the site is not ready. Ask whether the price covers anchoring: after the move you will re-anchor the shed, and our guide to anchoring a shed shows how.
Way 4: Take it apart
If the shed is too wide for the path, too weak to lift or too big for any trailer you can get, take it apart and rebuild. Bob Vila also notes that disassembling the shed as far as you can before movers arrive cuts the hourly charges.
What comes apart easily
Roof panels or shingles, trim, doors and windows come off first. Then the wall panels, if they are screwed or nailed in sections. Number each piece with a marker. Photograph the shed before you start.
What does not
Framing nailed in place and a glued subfloor take time to separate, and the wood gets damaged on the way. Pulling nails splits old studs. In that case, most of the lumber is better saved for blocking and scrap, and the shed is better rebuilt from a new cut list.
When to build from the parts
If you take the shed apart anyway, you are halfway to a build. The shed designer draws the cut list for any size from 48 inches wide, so you can see how much of the old lumber will go into the new shed and what is left to buy.
Why skids make a shed movable
A shed whose floor frame sits on skids can be moved without lifting the whole building. The skids are 4x6 pressure-treated timbers set on edge, and in our designer they run from the front of the shed to the back, as the drawing shows.
Skids make a shed movable because they are runners. You can put rollers or a trailer’s lifting gear under them, or run a chain to them. With a floor frame set on blocks or poured into a slab, there is nothing to hold. If you plan to move a shed one day, build it on skids. Our guide to a shed on skids has the skid count for each shed width and how to build the floor.
If your shed has no skids, a mover can add them. We Move Sheds lists $100 to add 4x4 skids, and $150 for larger buildings, plus material.
Is it worth moving a shed or building new
The answer depends on the shed and the move. Moving costs you a few hundred dollars, a day of work and some risk. Building costs you the materials and the weekends.
Move it when
The shed is sound, the floor is solid, and the trip is short. A local move at the numbers above is a small share of what a new shed costs in lumber alone.
Build new when
The floor is soft, the frame is racked or the shed is old enough that every joint is loose. You also build new when the move needs a crane, a wide-load permit or a long haul, because those jobs reach the cost of a new shed fast.
What a new one costs in materials
For comparison, this is the materials list for a 10x12 gable shed from our designer, priced at Home Depot in October 2026. It is materials only, with no labor, no permit and no foundation work beyond the gravel.
Shell $3,386.18, shed materials $4,322.47
Budget build $4,215.62 to typical $4,322.47.
| Buy | Item | Each | Line |
|---|---|---|---|
| Lumber | |||
| 4 | 4x6 pressure-treated (ground contact), 12 ft | $35.68 | $142.72 |
| 10 | 2x6 pressure-treated (ground contact), 10 ft | $12.68 | $126.80 |
| 2 | 2x6 pressure-treated (ground contact), 12 ft | $15.08 | $30.16 |
| 51 | 2x4 framing lumber, 8 ft | $4.35 | $221.85 |
| 12 | 2x4 framing lumber, 10 ft | $7.83 | $93.96 |
| 6 | 2x4 framing lumber, 12 ft | $9.42 | $56.52 |
| 2 | 2x4 framing lumber, 16 ft | $12.47 | $24.94 |
| 10 | 2x6 framing lumber, 8 ft | $9.97 | $99.70 |
| 2 | 2x6 framing lumber, 12 ft | $14.98 | $29.96 |
| 4 | 2x6 framing lumber, 16 ft | $19.96 | $79.84 |
| 1 | 2x8 framing lumber, 12 ft | $16.98 | $16.98 |
| 9 | 1x4 exterior trim board, 8 ft | $10.58 | $95.22 |
| 2 | 1x4 exterior trim board, 12 ft | $16.98 | $33.96 |
| 1 | 1x4 exterior trim board, 16 ft | $21.46 | $21.46 |
| 2 | 1x6 exterior trim board, 12 ft | $25.55 | $51.10 |
| Sheet goods | |||
| 5 sheets | 3/4" treated tongue-and-groove subfloor, 4x8 | $89.99 | $449.95 |
| 12 sheets | Panel siding, 19/32" T1-11 plywood, APA Rated Siding 303, Exterior (the wall bracing counts on this panel: a plywood wood structural panel 19/32" thick, over the 3/8" IRC Table R602.10.4 asks for CS-WSP; the bracing calculation does not cover a different siding or a thinner panel), 4x8 | $46.78 | $561.36 |
| 2 sheets | Panel siding for the gable ends, 4x8 | $46.78 | $93.56 |
| 1 roll | House wrap (water-resistive barrier), 9 ft x 100 ft roll | $82.67 | $82.67 |
| 7 sheets | 7/16" OSB roof sheathing, 4x8 | $11.98 | $83.86 |
| 3 pieces | Z-flashing for the horizontal siding joints, 10 ft pieces | $5.98 | $17.94 |
| 1 sheet | 1/2" plywood for the header spacers, 4x8 | $27.81 | $27.81 |
| Roofing | |||
| 5 bundles | Asphalt shingles, 3 bundles per square | $44.97 | $224.85 |
| 1 bundle | Starter strip shingles | $54.97 | $54.97 |
| 1 bundle | Hip and ridge cap shingles | $63.97 | $63.97 |
| 1 roll | Synthetic roof underlayment, 10-square roll | $74.98 | $74.98 |
| 2 lb | Plastic cap nails, 1-1/2", for the underlayment and the house wrap | $12.91 | $25.82 |
| 6 pieces | Drip edge, 10 ft pieces | $8.48 | $50.88 |
| Fasteners and hardware | |||
| 16 lb | Framing nails, 16d common, hot-dip galvanized, 3-1/2" x 0.162" | $31.73 | $126.92 |
| 6 lb | Toenail nails, 10d box, hot-dip galvanized, 3" x 0.128" | $19.38 | $38.76 |
| 15 lb | Siding nails, 8d common, hot-dip galvanized, 2-1/2" x 0.131" | $26.98 | $80.94 |
| 6 lb | Roof sheathing nails, 2-1/2" (8d) | $26.98 | $53.96 |
| 3 lb | Exterior screws for the subfloor, 2", rated for treated lumber | $34.47 | $34.47 |
| 20 | Rafter-to-plate connectors (hurricane ties) | $0.98 | $19.60 |
| 10 | Ridge straps, 1-1/4" x 20 ga galvanized steel, 18" long (Simpson Strong-Tie LSTA18 or equal) | $1.38 | $13.80 |
| 2 lb | Nails for the ridge straps, 10d common, 3" x 0.148", hot-dip galvanized | $4.97 | $9.94 |
| 4 lb | Roofing nails, 1-1/4" | $21.00 | $21.00 |
| 3 tubes | Construction adhesive (subfloor) | $7.68 | $23.04 |
| 4 | Earth auger anchors, 30 in or longer, with a holding rating published by their maker, plus galvanized cable and wire-rope clips | $50.89 | $50.89 |
| 200 nails | Connector nails for the hurricane ties, 0.131" x 2-1/2" galvanized | $8.55 | $25.65 |
| 18 | Plywood H-clips for 7/16" sheathing | $12.22 | $12.22 |
| Flashing, sealants and finish | |||
| 1 piece | Z-flashing for the door and window heads, 10 ft pieces | $5.98 | $5.98 |
| 1 roll | Window flashing tape, 4" x 75 ft roll | $36.42 | $36.42 |
| 3 tubes | Exterior acrylic-latex caulk, paintable, 10.1 oz | $2.98 | $8.94 |
| 3 | Exterior primer, 1 gallon | $29.98 | $89.94 |
| 5 | Exterior paint or solid stain, 1 gallon | $49.98 | $249.90 |
| Doors and windows | |||
| 2 | Shed window with a nailing flange, for a 24" x 24" rough opening | $46.99 | $93.98 |
| Door build | |||
| 2 | 2x4 framing lumber, 92-5/8" precut stud, for the door frames | $4.15 | $8.30 |
| 4 | 2x4 framing lumber, 8 ft, for the door frames | $4.35 | $17.40 |
| 4 | 1x2 furring strip, 8 ft, for door stops and the astragal | $1.54 | $6.16 |
| 1 sheet | Panel siding for the door skins, 4x8 | $46.78 | $46.78 |
| 6 | Heavy-duty T-hinges, 8" | $9.50 | $57.00 |
| 1 | Two-way gate latch, opens from inside and outside without a key | $28.98 | $28.98 |
| 1 | Padlock hasp, for locking the shed when it is empty | $5.97 | $5.97 |
| 2 | Barrel bolts for the fixed leaf | $8.27 | $16.54 |
| 2 | Door pull handle | $4.98 | $9.96 |
| 1 box | Exterior screws for the door frames and stops, 2-1/2" | $15.38 | $15.38 |
| 2 boxes | Exterior screws for the door skins, 1-1/4" | $10.98 | $21.96 |
| 2 tubes | Construction adhesive (door skins), 10 oz | $7.48 | $14.96 |
| Temporary bracing | |||
| 9 | 2x4 framing lumber, 8 ft, for temporary braces and stakes and ridge posts | $4.35 | $39.15 |
| 2 | 2x4 framing lumber, 16 ft, for temporary braces and stakes and ridge posts | $12.47 | $24.94 |
| 1 box | Exterior screws for the temporary braces, 3" | $24.88 | $24.88 |
| Foundation | |||
| 1 roll | Landscape fabric, enough to cover 12' x 14' | $49.97 | $49.97 |
| Shell: structure, siding, roof and foundation | $3,386.18 | ||
| Finish: doors, windows, trim, flashing, caulk, primer and paint | $936.29 | ||
| Shed materials, doors built from the plan (the cheaper door for this size), 63 of 63 lines priced | $4,322.47 | ||
| Materials priced: $4,322.47 · every line priced · Excluded: tax, delivery, labor, permits, tools | |||
| Labor if you hire it out, apart from the materials | $960 to $7,200 | ||
| Labor only, building the shed from the plan (framing, siding, roof, doors), materials not included, for the shed as a shell: insulating, wiring and lining the inside are not in this range. Published ranges (HomeGuide, Aug 2025: $8 to $60 per sq ft; Fixr, Mar 2024: $25 per sq ft), per sq ft from the examples they quote (a 10x10 custom build and a 10x12 wooden shed). 120 sq ft at $8 to $60 per sq ft, middle about $3,000. A range from guides, not a quote; get two local quotes. Separate from the materials above and not in their sum. | |||
| With pre-hung doors instead (closest available, $593.00: no pre-hung pair was found, this is a single 48 in leaf, special order), 52 of 52 lines | $4,586.12 | ||
| Budget build: the cheapest spec of this plan that passes every check | |||
| Frame rafters at 24 in on center | -$106.85 | ||
| Budget build, you save $106.85 | $4,215.62 | ||
| Optional: no window as well, $211.99 less | $4,003.63 | ||
| Site prep, not in the shed materials total | |||
| 2.8 cu yd | Gravel base: compactable crushed stone, loose, for a 4" compacted pad 1 ft wider than the shed on every side | $69.95 a bag | $195.86 |
Bulk prices and bigger packs on this list
- 2x4 x 8 ft: your list buys 64 boards, which reaches the bulk price. $27.52 less if the store applies it at the register: the card shows $3.92 a board at 50 or more, $4.35 below that (Home Depot, Bronx Terminal store, Sep 30, 2026).
- Connector nails: the list's 3 boxes of 1 lb are the same Grip-Rite 8d galvanized common nail it buys in 5 lb boxes for the siding and the roof sheathing. Buy 5 boxes of 5 lb for both jobs instead and save $25.65: $26.98 for 5 lb (model 8HGC5, Home Depot, Hamilton Mill store (ZIP 30011), Oct 8, 2026) against $8.55 for 1 lb (model 8HGC1, Home Depot, Hamilton Mill store (ZIP 30011), Oct 8, 2026).
- Exterior paint or solid stain: your list buys 5 gallons, which reaches the bulk price. $24.90 less if the store applies it at the register: the card shows $45.00 a gallon at 5 or more, $49.98 below that (Home Depot, Hamilton Mill store (ZIP 30011), Oct 8, 2026).
Left over in part-used boxes
Boxes of nails, screws and clips come whole, so about $133.56 of this list stays in part-used boxes: the shed itself uses that much less. Rolls and bundles of roofing and house wrap are sold whole too: about $139.02 of them stays unused on a small design.
- Framing nails: the shed uses 16 lb of the 20 lb you have to buy, about $25.38 left over.
- Toenail nails: the shed uses 6 lb of the 10 lb you have to buy, about $15.50 left over.
- Roof sheathing nails: the shed uses 6 lb of the 10 lb you have to buy, about $21.58 left over.
- Exterior screws for the subfloor: the shed uses 3 lb of the 5 lb you have to buy, about $13.79 left over.
- Roofing nails: the shed uses 4 lb of the 5 lb you have to buy, about $4.20 left over.
- Connector nails for the hurricane ties: the shed uses 200 nails of the 270 nails you have to buy, about $6.65 left over.
- Plywood H-clips for 7/16" sheathing: the shed uses 18 clips of the 50 clips you have to buy, about $7.82 left over.
- Exterior screws for the door frames and stops: the shed uses 69 screws of the 100 screws you have to buy, about $4.77 left over.
- Exterior screws for the door skins: the shed uses 108 screws of the 200 screws you have to buy, about $10.10 left over.
- Exterior screws for the temporary braces: the shed uses 40 screws of the 900 screws you have to buy, about $23.77 left over.
- House wrap: the shed uses 418 sq ft of the 900 sq ft in the roll or bundle you have to buy, about $44.27 left over.
- Starter strip shingles: the shed uses 49 lin ft of the 120 lin ft in the roll or bundle you have to buy, about $32.52 left over.
- Synthetic roof underlayment: the shed uses 1.7 squares of the 10 squares in the roll or bundle you have to buy, about $62.23 left over.
Our shed cost guide puts this next to what prefab and builder prices look like. If you build new, the free 10x12 plan gives you the full cut list.
The gear to buy
Whichever way you go, the gear is short. A pair of bottle jacks or screw jacks rated well above the weight of one corner, a set of heavy-wall PVC or steel pipe rollers, ratchet straps and a few lengths of 4x4 for cribbing cover most home moves, and they are cheaper to buy than to rent for a weekend.
After the move
Set the shed on the new base, check it is level across both axes, and shim under the skids if it is not. Walk through the door, because a shed that has moved may have racked, and a door that binds shows it. Then anchor it, following the anchoring guide, and check your local building department if the new address changes any setback or permit.
Sources
Every number in this guide that does not come from our own shed designer was checked against these 2 documents, numbered in the order the text first cites them and read on Oct 29, 2026. 2 are codes, agencies, makers and stores.
- 1Bob VilaHow Much Does It Cost to Move a Shed?
- 2We Move ShedsShed Moving Prices


